Configuration
The IR Blasters are shipped already prepared to be used in your DisplayHUB system and should be plug and play however there are times that the WiFi configuration of the blaster might need to be updated:
The DisplayHUB IR Blasters are configured by connecting your computer to the SSID labeled “IRBlaster” and then entering “displayhub” for the password. Your browser should automatically launch and go to http://192.168.4.1, this is where you enter the DisplayHUB appliance WiFi credentials. The default credentials are already entered, just click save! Only change the defaults if you are instructed by customer support to do so.
In order to use your DirecTV receivers with DisplayHub, they must be enabled in the set-top box by navigating to the
“External Device” settings screen (Menu->System Setup->Whole-Home->External Device) screen.
Once on this screen select “Allow” for “External Access”
Some DirecTV receivers will fall asleep and become unresponsive to DisplayHub, to avoid this issue make sure all receivers have this mode disabled.
Press {MENU}.
Arrow down to “Settings” and press {SELECT}
Arrow over so “Settings & Help” is highlighted and press {SELECT}.
Arrow down to “Power Saving” and press {SELECT}.
Select NO and save
Leave a Reply
You must be logged in to post a comment.
The first green light is the system light, it indicates if there is power and will blink when the appliance calls home.
The middle light indicates if the system has an internet connection. This light checks for an internet connection every 60 seconds, if internet is not found, the light will flash several times and then system will reboot.
The last light is a red Wifi traffic indicator.
Leave a Reply
You must be logged in to post a comment.
To teach a remote command go to your IR Blasters Configuration screen.
Locate the IR Blaster you want to learn commands from by clicking the “Blink Light Button”, this will flash a light on the IR Blaster for 1 minute. Once you are sure you have located the proper IR Blaster you will now locate the learning port on the device (small hole and labled). This is where you will aim your teaching remote.
Now click “Remote Buttons”, click add button, give your button a name, then point your teaching remote at the learning port on the iR blaster and briefly push the button you are teaching/learning. The IR blaster will blink confirming it registered your code in it’s memory.
TIP: push the button for only a split second, some remotes repeat commands in rapid succession, this will produce a code that the IR Blaster can not understand.
After the IR Blaster registered a code in it’s memory, click the “Get last IR code learned” button, this will copy the command from the IR Blaster into the button you have created.
TIP: most button commands will be very long (32 bits) and will look similar to this example: {‘data’:[9018,4484,588,546,586,546,586,542,588,546,584,542,588,512,616,542,586,546,588,1662,586,544,590,540,584,514,618,542,588,540,588,510,618,1666,586,544,586,1666,584,1666,586,1666,588,546,588,1664,588,542,588,542,588,1666,588,542,584,546,590,538,588,1664,588,544,584,1666,588,1660,584],’type’:’raw’,’khz’:38}
TIP: The command you just retrieve should be at least slightly different than the previous.
With the IR Blaster connected to the device you are attempting control, click the “Test” button, your command should be sent to the IR Blaster which will then convert it back into an IR signal that will produce the desired result.
Continue adding buttons, once you have added the buttons you wish to use (not all are needed) simple click save.
That’s it! You have taught your remote to the DisplayHub system! Don’t forget to associate the IR Blaster to a port/device
For color buttons, simply use the color name like RED for the button label.
For CC / Closed Captioning use “CC”.
Some odd devices use special characters for channel numbers etc. For example, our EPG’s supply digital channel numbers with – (dash) but your device might want to receive a . (period / dot) for seperation of the numbers in a digital channel, this is can be fixed by simply teaching your remote a command of – (dash) with the IR code for a . (period / dot).
For all other buttons simply use the same character, for example, some want to use “period” for dots, simply use a single . (period).
Leave a Reply
You must be logged in to post a comment.
Yes, you can add more devices anytime within the limits of your subscription and main switch.
Example, you purchased a 23 device subscription and have a 24 port switch with open ports available you can add devices by purchasing more input and/or output adapters.
If you have run out of ports contact us about our trade in program.
Leave a Reply
You must be logged in to post a comment.
Yes, with a “but”. These devices to not have a native way of controlling them via IP so we developed custom IR Blasters that need to be mounted to the device. DisplayHub will automatically discover these blasters allow you to configure them. We currently only have pre-programmed remote codes for Spectrum but we are happy to custom code IR Blasters with the data needed to control your device but we will need you to send that device in to us. We typically have a turnaround of about 2 days for this service. IR Blasters are $119 each. Please contact us for move info.
We also offer custom IR Blasters to control TouchTunes, AMI, zoned amplifiers and other devices can be integrated.
Leave a Reply
You must be logged in to post a comment.
Of course! You can add any device with an HDMI output. We can also offer built in digital signage for an additional fee (subscription based). Please contact us to learn more.
Leave a Reply
You must be logged in to post a comment.
Installation
Activate Online
After you complete the receiver setup, DIRECTV allows you to activate the receiver online. To do this, open an Internet browser and navigate to the DIRECTV website. Click “My Account” in the upper-right corner of the window. Click on the “My Equipment” tab. Click the “Update” button next to your receiver’s name. The receiver’s name is usually DVR or Standard. Type the access code number and model number of the receiver. Enter the receiver ID. To find out your receiver’s ID, open the access card door panel and look for a sticker inside. The receiver ID is written on the sticker.
Call DIRECTV
If you cannot access the Internet or the DIRECTV website, DIRECTV customer service will activate your receiver over the phone. Call customer service at 1-800-531-5000. DIRECTV offers general support from 8 a.m. to 1 a.m. (EST), seven days a week. They offer technical support 24 hours a day, seven days a week. When you call, have your receiver ID, model number, and access card number ready.
Activate a Used Receiver
DIRECTV lets you activate a used receiver in certain circumstances. If the receiver has no receiver ID, you cannot activate it. A receiver without an ID is too old to work with the current DIRECTV service. The receiver must have been owned, not leased. It must also not be active on a different DIRECTV account. If you think that your receiver meets these conditions, call DIRECTV customer service. To activate the receiver, you need to order a new access card for $20. After installing the receiver and new access card, call DIRECTV again for activation. Let customer service know that you have a used receiver.
The IR Blasters are shipped already prepared to be used in your DisplayHUB system and should be plug and play however there are times that the WiFi configuration of the blaster might need to be updated:
The DisplayHUB IR Blasters are configured by connecting your computer to the SSID labeled “IRBlaster” and then entering “displayhub” for the password. Your browser should automatically launch and go to http://192.168.4.1, this is where you enter the DisplayHUB appliance WiFi credentials. The default credentials are already entered, just click save! Only change the defaults if you are instructed by customer support to do so.
In order to use your DirecTV receivers with DisplayHub, they must be enabled in the set-top box by navigating to the
“External Device” settings screen (Menu->System Setup->Whole-Home->External Device) screen.
Once on this screen select “Allow” for “External Access”
Leave a Reply
You must be logged in to post a comment.
Some DirecTV receivers will fall asleep and become unresponsive to DisplayHub, to avoid this issue make sure all receivers have this mode disabled.
Press {MENU}.
Arrow down to “Settings” and press {SELECT}
Arrow over so “Settings & Help” is highlighted and press {SELECT}.
Arrow down to “Power Saving” and press {SELECT}.
Select NO and save
Leave a Reply
You must be logged in to post a comment.
The first green light is the system light, it indicates if there is power and will blink when the appliance calls home.
The middle light indicates if the system has an internet connection. This light checks for an internet connection every 60 seconds, if internet is not found, the light will flash several times and then system will reboot.
The last light is a red Wifi traffic indicator.
Leave a Reply
You must be logged in to post a comment.
To teach a remote command go to your IR Blasters Configuration screen.
Locate the IR Blaster you want to learn commands from by clicking the “Blink Light Button”, this will flash a light on the IR Blaster for 1 minute. Once you are sure you have located the proper IR Blaster you will now locate the learning port on the device (small hole and labled). This is where you will aim your teaching remote.
Now click “Remote Buttons”, click add button, give your button a name, then point your teaching remote at the learning port on the iR blaster and briefly push the button you are teaching/learning. The IR blaster will blink confirming it registered your code in it’s memory.
TIP: push the button for only a split second, some remotes repeat commands in rapid succession, this will produce a code that the IR Blaster can not understand.
After the IR Blaster registered a code in it’s memory, click the “Get last IR code learned” button, this will copy the command from the IR Blaster into the button you have created.
TIP: most button commands will be very long (32 bits) and will look similar to this example: {‘data’:[9018,4484,588,546,586,546,586,542,588,546,584,542,588,512,616,542,586,546,588,1662,586,544,590,540,584,514,618,542,588,540,588,510,618,1666,586,544,586,1666,584,1666,586,1666,588,546,588,1664,588,542,588,542,588,1666,588,542,584,546,590,538,588,1664,588,544,584,1666,588,1660,584],’type’:’raw’,’khz’:38}
TIP: The command you just retrieve should be at least slightly different than the previous.
With the IR Blaster connected to the device you are attempting control, click the “Test” button, your command should be sent to the IR Blaster which will then convert it back into an IR signal that will produce the desired result.
Continue adding buttons, once you have added the buttons you wish to use (not all are needed) simple click save.
That’s it! You have taught your remote to the DisplayHub system! Don’t forget to associate the IR Blaster to a port/device
For color buttons, simply use the color name like RED for the button label.
For CC / Closed Captioning use “CC”.
Some odd devices use special characters for channel numbers etc. For example, our EPG’s supply digital channel numbers with – (dash) but your device might want to receive a . (period / dot) for seperation of the numbers in a digital channel, this is can be fixed by simply teaching your remote a command of – (dash) with the IR code for a . (period / dot).
For all other buttons simply use the same character, for example, some want to use “period” for dots, simply use a single . (period).
Leave a Reply
You must be logged in to post a comment.
Yes, you can add more devices anytime within the limits of your subscription and main switch.
Example, you purchased a 23 device subscription and have a 24 port switch with open ports available you can add devices by purchasing more input and/or output adapters.
If you have run out of ports contact us about our trade in program.
Leave a Reply
You must be logged in to post a comment.
Yes, with a “but”. These devices to not have a native way of controlling them via IP so we developed custom IR Blasters that need to be mounted to the device. DisplayHub will automatically discover these blasters allow you to configure them. We currently only have pre-programmed remote codes for Spectrum but we are happy to custom code IR Blasters with the data needed to control your device but we will need you to send that device in to us. We typically have a turnaround of about 2 days for this service. IR Blasters are $119 each. Please contact us for move info.
We also offer custom IR Blasters to control TouchTunes, AMI, zoned amplifiers and other devices can be integrated.
Leave a Reply
You must be logged in to post a comment.
Of course! You can add any device with an HDMI output. We can also offer built in digital signage for an additional fee (subscription based). Please contact us to learn more.
Leave a Reply
You must be logged in to post a comment.
irBlasters
The IR Blasters are shipped already prepared to be used in your DisplayHUB system and should be plug and play however there are times that the WiFi configuration of the blaster might need to be updated:
The DisplayHUB IR Blasters are configured by connecting your computer to the SSID labeled “IRBlaster” and then entering “displayhub” for the password. Your browser should automatically launch and go to http://192.168.4.1, this is where you enter the DisplayHUB appliance WiFi credentials. The default credentials are already entered, just click save! Only change the defaults if you are instructed by customer support to do so.
Pre Sales
Yes, you can add more devices anytime within the limits of your subscription and main switch.
Example, you purchased a 23 device subscription and have a 24 port switch with open ports available you can add devices by purchasing more input and/or output adapters.
If you have run out of ports contact us about our trade in program.
Leave a Reply
You must be logged in to post a comment.
Yes, with a “but”. These devices to not have a native way of controlling them via IP so we developed custom IR Blasters that need to be mounted to the device. DisplayHub will automatically discover these blasters allow you to configure them. We currently only have pre-programmed remote codes for Spectrum but we are happy to custom code IR Blasters with the data needed to control your device but we will need you to send that device in to us. We typically have a turnaround of about 2 days for this service. IR Blasters are $119 each. Please contact us for move info.
We also offer custom IR Blasters to control TouchTunes, AMI, zoned amplifiers and other devices can be integrated.
Leave a Reply
You must be logged in to post a comment.
Of course! You can add any device with an HDMI output. We can also offer built in digital signage for an additional fee (subscription based). Please contact us to learn more.
Leave a Reply
You must be logged in to post a comment.
Leave a Reply
You must be logged in to post a comment.