DisplayHUB / Knowledge wiki
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
| android:aio [2026/11/22 02:25] – created - external edit 127.0.0.1 | android:aio [2026/11/22 19:15] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== DisplayHUB | + | ====== DisplayHUB |
| ===== Controller-free encoder mode ===== | ===== Controller-free encoder mode ===== | ||
| - | DisplayHUB | + | DisplayHUB |
| - | Use a trusted local network that allows device-to-device communication | + | **Only one DisplayHUB AIO encoder per network.** Multiple AIO encoders can send conflicting playback commands. For more than one encoder, use a [[: |
| + | |||
| + | See the [[https:// | ||
| + | |||
| + | The subscription service issues a renewable Encoder session through the fields already understood by deployed players. These sessions do not register devices against ordinary Controller seats. Entering a raw AIO Stripe subscription ID in a Controller is still rejected. | ||
| + | |||
| + | Use a trusted local network that allows device-to-device communication, UDP discovery, and local HTTP commands. Guest Wi-Fi, client isolation, VLAN rules, or firewalls can prevent discovery or playback. Legacy players and the Encoder must use the same public internet egress address for subscription validation. IPv6 addresses that differ by device, separate VPNs, or different internet gateways can prevent session validation. | ||
| + | |||
| + | ===== Set up AIO ===== | ||
| + | [[https:// | ||
| + | |||
| + | Copy the subscription ID from the AIO confirmation page and keep it private. [[https:// | ||
| - | ===== Set up Aio ===== | ||
| - Connect the HDMI source, USB capture device, and Android Encoder. Grant the Android camera, audio, USB, and notification permissions required by the selected input. | - Connect the HDMI source, USB capture device, and Android Encoder. Grant the Android camera, audio, USB, and notification permissions required by the selected input. | ||
| - Open the Encoder configuration page from a browser on the same network. | - Open the Encoder configuration page from a browser on the same network. | ||
| - | - Open **Aio Settings**, enter the subscription ID for an active or trialing DisplayHUB | + | - Open **AIO Settings**, enter the subscription ID for an active or trialing DisplayHUB |
| - The Encoder starts its configured input when Android permissions and input settings allow it. Compatible decoders on the local network are discovered and sent the live stream. | - The Encoder starts its configured input when Android permissions and input settings allow it. Compatible decoders on the local network are discovered and sent the live stream. | ||
| - | An Aio subscription is separate from a regular controller subscription. | + | An AIO subscription is separate from a regular controller subscription. |
| + | |||
| + | The AIO settings section remains available when the configuration page is opened directly, even if a Controller address is already saved. Opening the configuration page from a Controller hides AIO controls. The header shows one shortcut: **Controller** when it is available and AIO is off, otherwise **AIO Settings**. The AIO section header collapses or expands its settings, and **AIO Settings** expands it automatically. The one-AIO-encoder-per-network warning remains visible when the settings section is collapsed. | ||
| ===== Stream delivery ===== | ===== Stream delivery ===== | ||
| - | By default, | + | By default, |
| - | Keep the Encoder and decoders powered and connected to the same routable LAN. Aio discovery runs only while Aio mode is enabled. A decoder that becomes available after startup is discovered automatically. | + | Roku commands use HLS automatically. Roku requires the DisplayHUB channel to be installed and network app control enabled. webOS requires its DisplayHUB local command service to be available. Samsung/ |
| + | |||
| + | Keep the Encoder and decoders powered and connected to the same routable LAN. AIO discovery runs only while AIO mode is enabled. A decoder that becomes available after startup is discovered automatically. | ||
| + | |||
| + | The AIO settings show network-scan progress, the number and types of players found, scan completion even when no players are found, and Samsung/ | ||
| + | |||
| + | Discovery uses SSDP announcements and a bounded private IPv4 sweep for networks up to /23. Larger networks rely on discovery announcements. A device must expose a recognized DisplayHUB app or command service before the Encoder sends playback to it. Compatibility with RDK, Xfinity, and other players without a confirmed command interface is not established. | ||
| ===== Encoder features ===== | ===== Encoder features ===== | ||
| - | The Encoder' | + | The Encoder' |
| + | |||
| + | The Encoder can switch to controller mode without a separate installer. Google Play billing is not currently supported for AIO; follow the billing option shown for the subscription. | ||
| - | The Encoder | + | ===== Digital signage ===== |
| + | DisplayHUB AIO can also operate as a standalone digital-signage source. Its included Overlay Editor combines the configured video with text, logos, images, slideshows and supported | ||
| ---- | ---- | ||
| [[: | [[: | ||
Read-only public knowledge base, maintained through the site's deployment files. Powered by DokuWiki. Device and firmware behavior must be qualified on your actual equipment.
Start here